Six knobs and two keys
Drag a knob up or down (hold Shift for fine steps), double-click it to return to its default, or click its value to type a number.
Drive · 0 to 24 dB · default 3 dB
How hard the signal is pushed into the saturator. With Auto gain on (the default), Drive mostly adds saturation, not loudness.
Harmonics · 0 to 100 % · default 50 %
Which harmonics are added. Toward 0 % the even (2nd) harmonic grows; at 100 % only odd harmonics remain.
Amount · 0 to 100 % · default 50 %
How much saturated sound is used inside the processor. At 0 % the signal passes clean. Auto gain follows Amount, keeping the level roughly even.
Edge · −50 to +50 · default 0
How the saturation curve bends. Negative bends softly; positive bends harder and flattens loud peaks. Quiet material changes little.
Mix · 0 to 100 % · default 100 %
A final blend of your original signal with the processed result, kept in time.
Output · −24 to +12 dB · default 0 dB
Final level after Mix. It does not change the saturation.
Power key (bypass)
Lit: processing on. Unlit: bypassed; the original passes through, kept in time. Output is not applied while bypassed.
TUNING LAB key
Opens the Tuning Lab.
Amount or Mix?
Amount works inside the saturator, with Auto gain re-balancing the level. Mix blends the result with your original at the end.
Harmonics or Edge?
Harmonics picks which harmonics are added. Edge picks how abruptly louder material bends.
Tuning Lab
Ten deeper settings for the saturator. Open it with the TUNING LAB key; press BACK (or Esc) to return. Audio keeps running, and every change glides over 30 ms.
The Tuning Lab replaces the front panel in the same window.
A and B
Two complete tunings. Click A or B to listen to one; the six front-panel knobs stay shared. Copy to other copies the slot you are hearing into the other slot.
Adjusting a setting
Drag a slider (hold Shift for fine steps) or click its value to type a number. Double-click a slider to return that one setting to its factory value.
The line under the title
Shows which slot you are hearing and the gain going into the saturator.
Factory Reset
Returns the slot you are hearing to the factory tuning. The front-panel knobs and your saved default stay as they are.
Signal flow
Input → Drive → Saturator → Amount → Auto gain → Mix → Output
Level: four settings (collapsible)
These four set levels: how hard the signal meets the saturator, and how loud it leaves. The far ends of each range are experimental.
Max internal Drive · 0 to 36 dB · factory 24 dB
What it does: Sets how much gain the Drive knob reaches at its top. The knob still reads 0 to 24 dB, and its automation range does not change.
When to adjust it: Raise it if Drive at maximum is not enough. Lower it to spread a smaller range over the whole knob for finer steps.
Input calibration · −12 to +12 dB · factory 0 dB
What it does: A level offset into the saturator, added to Drive. At +6 dB the same Drive setting hits the curve 6 dB harder. Auto gain compensates the output level.
When to adjust it: For sources that are much quieter or louder than usual, so Drive reacts in a similar range.
Auto gain · 0 to 1× · factory 1×
What it does: At 1, the output level of a −18 dBFS RMS sine stays the same as Drive, Amount or Edge change. At 0 there is no compensation, and Drive also raises the output level.
When to adjust it: Keep it at 1 to compare settings at an even level. Lower it if you want Drive to make the signal louder as well.
Output correction · −12 to +12 dB · factory 0 dB
What it does: A fixed level trim added to the Output knob. It also applies when Amount or Mix is at 0, but not while bypassed.
When to adjust it: To keep a lasting level offset with this tuning without moving the Output knob.
Character: six settings (collapsible)
These six change the saturation itself: where the even harmonics come from and how much of them there is, how much bass drives the saturator, and the reach of the Edge knob.
Asymmetry (even source) · 0 to 1.5 · factory 0.6
What it does: Makes the positive half of the wave saturate earlier than the negative half. This is where the even harmonics come from; at 0 there are none.
When to adjust it: Raise it for more even-harmonic content, lower it for less. It works together with Harmonics and Even / H2 strength.
Even / H2 strength · 0 to 1 · factory 1
What it does: How much of the even part is used at Harmonics 0 %. Harmonics scales it by (1 − Harmonics)², which is 25 % at the default 50 %. At 0, only odd harmonics remain at any Harmonics setting.
When to adjust it: Lower it to limit how much even content the Harmonics knob can reach.
Overall harmonic Amount · 0 to 2× · factory 1×
What it does: Multiplies the Amount knob. The result is capped at full strength, so the curve never folds back.
When to adjust it: Above 1× to reach full strength earlier on the Amount knob; below 1× to limit the strongest setting.
Bass excitation · −12 to 0 dB · factory −3 dB
What it does: Lowers the part below about 120 Hz that drives the saturator. The dry bass is untouched.
When to adjust it: Lower it when you want the low end to drive the saturation less; raise it toward 0 dB to let the bass drive it fully. Listen to the low end while you change it.
Even-path high-pass · 5 to 80 Hz · factory 35 Hz
What it does: A high-pass filter on the even part only. It removes the very low-frequency content and offset that asymmetric saturation creates.
When to adjust it: Raise it if strong even settings add unwanted low-frequency energy (a spectrum analyser shows it); lower it to keep more of the even part’s low end.
Edge span · 0 to 2× · factory 1×
What it does: Scales the Edge knob. At 2× the softest and hardest curves are reached at Edge ±25; at 0 the Edge knob has no effect.
When to adjust it: Raise it to reach the extremes with less knob travel; set it to 0 to lock Edge at the centre curve.
Installing
Polite Voltage comes as one folder, Polite Voltage.vst3. Installing means copying that folder to the place where Windows plug-ins live.
Before you start
Windows, 64-bit. Tested on Windows 11.
A 64-bit VST3 host (your DAW).
No Visual C++ Redistributable or other runtime is needed.
Install
Close your DAW.
Copy the whole folder Polite Voltage.vst3 into C:\Program Files\Common Files\VST3\. Windows may ask for administrator permission.
Start your DAW. If Polite Voltage does not appear, rescan your plug-ins.
Keep only one copy of Polite Voltage in your VST3 folders.
First sound
Insert Polite Voltage on a mono or stereo track and play some audio. It opens at its default settings and is already processing.
Turn Drive up slowly. Auto gain keeps the level close to where it was, so what changes is the amount of saturation.
Choose the character. Harmonics moves between even and odd harmonics; Edge moves between a soft and a hard curve.
Set how much. Amount sets the strength, Mix blends in your original. Press the power key to compare with the bypassed sound.
Saving
Your DAW session or preset
Saves everything: the six knobs, the power key, and both Tuning Lab slots with the one selected. Polite Voltage has no preset list of its own, so use your DAW to store presets.
Save Default (Tuning Lab)
Saves the slot you are hearing as the starting tuning for new instances, in both A and B. Sessions you already have keep their own settings. File: %APPDATA%\PoliteVoltage\tuning-default.json
Load Default
Loads your saved default into the slot you are hearing.
Export JSON / Import JSON
Export writes both slots and the selected slot to a file you choose; Import loads them back. The six front-panel knobs are not in the file. An invalid file is refused and your current settings stay.
Back to factory for new instances
Press Factory Reset, then Save Default.
Where to start
Directions to explore, not recipes. Move one knob at a time and listen.
Bass
Raise Drive slowly with the bass playing in the full mix. Lower Harmonics adds more of the even (2nd) harmonic; higher keeps to odd harmonics. To let the lowest notes drive the saturation less, lower Bass excitation in the Tuning Lab.
Drums
Edge changes how hard loud peaks are bent, so try it in both directions on the hits. Mix below 100 % blends the untouched drums back in alongside the processed sound.
Synth
Hold a sustained note and sweep Harmonics from even to odd. Then set Drive for how far it saturates, and Amount for how much of it you keep.
Results depend on input level. The same settings saturate a loud track more than a quiet one. Auto gain is calibrated for a level of −18 dBFS RMS; for much quieter or louder tracks, adjust Drive or Input calibration.
Polite Voltage reports a latency of 135 samples to your host, which compensates for it automatically.
Download
Polite Voltage 0.1.0 · Free Beta
Download for Windows User Guide (PDF)
Requirements
Included in the download
Known limitations
Windows only.
Beta release. Save and back up your projects.
Not code-signed, so a download or security warning can appear.
Update history
If something is not right (collapsible)
Polite Voltage does not appear in my DAW
Check that the whole folder Polite Voltage.vst3 is in C:\Program Files\Common Files\VST3\, not only the file inside it. Make sure your DAW is 64-bit and scans that folder, then rescan your plug-ins. Keep only one copy.
Windows or my browser shows a warning
Polite Voltage is not code-signed, so a download or security warning can appear. Download it only from this page.
It is too loud
Lower Output. If Auto gain in the Tuning Lab is below 1, Drive also raises the level. Polite Voltage has no built-in limiter.
Bypass sounds louder or quieter
Output is not applied while bypassed, so a raised or lowered Output makes the comparison uneven.
Tuning Lab changes make no difference
At Amount 0 % or Mix 0 % no saturation reaches the output, so the saturation settings have no effect. Raise Amount and Mix first.
Uninstalling
Close your DAW and delete C:\Program Files\Common Files\VST3\Polite Voltage.vst3. If you used Save Default, you can also delete %APPDATA%\PoliteVoltage\tuning-default.json.
Made by Minon Ryu
Thank you for listening.
Questions and bug reports: Support@minonryu.com
If you would like to support the project (optional):
Support via PayPal ↗ (https://paypal.me/MinonRyu)
License and third-party notices are included in the download (EULA.txt, THIRD_PARTY_NOTICES.txt).
VST is a registered trademark of Steinberg Media Technologies GmbH.
© 2026 Minon Ryu